Road-Tripping in a Non-Tesla 100% EV

You cannot escape the responsibility of tomorrow by evading it today.

Abraham Lincoln

I have the unique pleasure of working with an employee-owned organization, Melink Corporation, that is dedicated toward making the world a better place. Our vision is to help advance clean energy such that it transforms the world through improving our global economy, security and environment – for ourselves, our children and future generations.

Though energy efficiency and renewable energy are at the core of what we do, sustainability is central to who we areIf we don’t lead by example, who will? So, in addition to operating a Net-Zero LEED® Platinum headquarters facility, we have a super-green fleet of vehicles. Our National Network of Service Technicians each drive hybrid vehicles. Our parking lot has over twenty electric-vehicle charging stations. In total we have over forty hybrids and seventeen EVs in our fleet driven. 61% of our employees drive either hybrid or electric.

I, personally, drive a 2018 Chevy Bolt and have done so for about nine months. The car has a 238 EPA estimated range and does not have the luxury of accessing Tesla’s Supercharging Network. I have a 45 mile commute, one-way from my home to my office. Fortunately, by driving an EV, living in a home and working in an office that are both powered by renewable energy, my ‘electric gas’ is very clean. I have three young kids, and it is very important to my wife and I, that we set a good example; not only so we guide them toward making their own integrity-based decisions as they mature, but also so in a direct effort preserve their future. As Abraham Lincon said, You cannot escape the responsibility of tomorrow by evading it today.

This month was the first time I took the Bolt on a good old fashion, American road-trip. I knew it would be a challenge but as another President said, nothing in the world is worth doing unless it means effort pain and difficulty. Here’s how it was (and can be) done.

The Hardware. You’ve got to have an EV that has an extended range. Here’s a list, for your reference, of the longest range EVs on the market today. But you’ve also got to have the capacity for Level 3 charging. On the Chevy Bolt the hardware cost an incremental $750, from the factory. GM advertises 90 miles of charge in 30 minutes, up to the 80% mark and the speed begins to taper to protect the battery.

The Fuel. There are of course Plug-in Hybrid EVs such as the Chevy Volt and Honda Clarity. Those models have about 30 – 50 miles of battery capacity with traditional gasoline as a backup. This isn’t the kind of EV I’m talking about here; I’m talking about 100% electrons. And I must acknowledge that during my road trip the electrons pulled from the grid may be coming from brown-power sources; but not necessarily. Wal-Mart, for example, has solar on many of their locations. And one of the two EVgo stations I charged at was at a Wal-Mart. Nonetheless, what’s the advantage of driving an EV vs. a traditional internal-combustion engine that uses gasoline? For one, EVs convert about 60% of their energy from the grid to power at the wheels; gasoline only converts about 19% of the energy stored to the wheels. Also, electricity, even from a coal-fired power plant, is a domestic energy source. Finally, you can get your electricity from renewable sources such as solar and wind.

The Apps. Before making any long-distance road trip, pre-planning the locations of charging stations (and their distances from one another), is critical. There are a number of apps you can use to see what’s out there: PlugShareChargePoint, and EVgo are the ones I use.

The Infrastructure. EVgo is America’s largest Public Electric Vehicle Fast Charging Network, with over 1,000 chargers in 66 markets. As a non-Tesla driver, this network is vitally important for the emerging EV market.

The Planning. A few days before my trip from Southwest Ohio to Eastern Tennessee, a 350 mile commute, I identified two Level 3 Fast charging stations and one Level 2 charging station for my trip. The first Level 3 charger I stopped at was only 35 miles from my house, located at a Wal-Mart in Florence, Kentucky. I topped off and drove another 239 miles to Knoxville, Tennessee… quite literally almost no margin for error between charging stations. Fortunately, during my planning I learned of an EVgo charging station that’s being installed about 3/4 that distance, along I-75 near Williamsburg, Kentucky. So the infrastructure is continuing to develop. After making it to the next fast-charger in Knoxville… I had 8 miles to spare. Nonetheless, I made it. So I charged for about one hour (180 miles). While I waited I was able to eat lunch and catch-up on some work. Then I drove another 35 miles to my final destination, which was for business purposes There I stayed for about 30 hours, plugged in to a residential 120V outlet at 12 amps. I got my charge up to about 90% before making the return trip… back to Knoxville, then to Florence, then home. Similar to my first-leg, I made it back to the Florence charger with about 6 miles to spare.

Lessons Learned. For one, my tire pressure was relatively low when I left my house. It took the necessity of my thin battery margin to realize the impact it had on my mileage efficiency. So, I filled them almost to max-pressure and the Bolt was ‘intelligent’ enough to roll this new information into its algorithm, thus giving me an increased range by about 10 miles from where I was before. Second, I noticed that by turning off my air conditioning, the algorithm gave me another 10 mile boost in my range. Also, I tried to keep my speed (on I-75, no less) at around 65 mph. You’ll notice in this chart the relationship between speed and range; the faster you drive, the less efficient your mileage.

In order to change the world, we’ve got to do things differently. Otherwise, if we continue to do the same things, nothing will change. This trip wasn’t easy. An otherwise normal five-hour trip took me about seven-hours, one way. I didn’t want to leave the house at 5am and I certainly didn’t want to get home at 2am. But I wanted to demonstrate it could be done, in the hope that just maybe it inspires others to make the leap, not only to an EV, but to a brighter future.

Geothermal Codes and Standards

Standardization has always been the hallmark of American way of life and its position as a global leader in achieving protection of public health, safety and welfare. This has been true in every industry and the geothermal industry is no different. This piece will highlight the best practices, standards and codes that have been developed over the years by this ‘relatively nascent’ industry.

The International Ground Source Heat Pump Association (IGSHPA), has led the way in design and installation standards for closed loop geothermal heat pump systems. Over the years, this volunteer group of industry experts have perfected design guidelines, pipe and joining methods, flushing, flow testing and antifreeze selection. Their latest version also addresses source water piping, water quality and treatment.

Another industry standard that has gone through the ANSI process is the new ANSI/CSA/IGSHPA C448 Series-16 Bi-National standard that covers five different types of heat exchangers including horizontal, surface water and open loop systems. This is the first edition of the bi-national series and covers both residential and commercial geothermal systems.

As far as codes and its application is concerned, the geothermal industry has effectively been a subset of the hydronics industry. Both the International Mechanical Code and Uniform Mechanical code have addressed it, but only in bits and pieces. The first comprehensive code was launched just last month (August 2018) by International Officials of Plumbing and Mechanical Officials (IAPMO) and is called the Uniform Solar, Hydronics and Geothermal Code (USHGC). This code includes systems where equipment and components collect, convey, store, and convert the sun’s energy and geothermal for a purpose including but not limited to service water heating, pool water heating, space heating and cooling and electrical service. This will serve as a great reference document for Authorities Having Jurisdiction over the installation of geothermal systems.

We at Melink take pride in our membership with various industry associations including IGSHPA and IAPMO and are honored to be contributing members of these groups. We also ensure all our design and installs adhere to the above standards and applicable codes.

It all fits in our vision to drive the industry by ‘innovating without reinventing’.